View MC74HC4016A_5001946.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

semiconductor technical data 31 rev 0 ? motorola, inc. 1995 10/95
" #! "!$ "!$ highperformance silicongate cmos th e m c54/74hc4016 a u tilize s s ilicongat e c mo s t echnolog y t o achieve f as t p ropagatio n d elays , l o w o n r esistances , a n d l o w o ff channel leakage current. this bilateral switch/multiplexer/demultiplexer controls a nalo g a n d d igita l v oltage s t ha t m a y v ar y a cros s t h e f ull powersupply range (from v cc to gnd). the hc4016a is identical in pinout to the metalgate cmos mc14016 and mc14066. each device has four independent switches. the device has been designed so that the on resistances (r on ) are much more linear over input voltage than r on of metalgate cmos analog switches. this device is identical in both function and pinout to the hc4066a. the on/off control inputs are compatible with standard cmos outputs; with pullup r esistors , t he y a r e c ompatible w it h l stt l o utputs . f o r a nalog switches with voltagelevel translators, see the hc4316a. for analog switches with lower r on characteristics, use the hc4066a. ? fast switching and propagation speeds ? high on/off output voltage ratio ? low crosstalk between switches ? diode protection on all inputs/outputs ? wide powersupply voltage range (v cc gnd) = 2.0 to 12.0 volts ? analog input voltage range (v cc gnd) = 2.0 to 12.0 volts ? improved linearity and lower on resistance over input voltage than the mc14016 or mc14066 ? low noise ? chip complexity: 32 fets or 8 equivalent gates logic diagram 1 13 4 5 8 6 11 12 2 3 9 10 a on/off control b on/off control c on/off control d on/off control x a x b x c x d y a y b y c y d analog outputs/inputs analog inputs/outputs = x a , x b , x c , x d pin 14 = v cc pin 7 = gnd this document contains information on a product under development. motorola reserves the right to change or discontinue this product without notice.

function table pin assignment x b y b y a x a gnd c on/off control b on/off control 11 12 13 14 8 9 10 5 4 3 2 1 7 6 y d x d d on/off control a on/off control v cc x c y c on/off control state of input analog switch l off h on d suffix soic package case 751a03 n suffix plastic package case 64606 ordering information mc54hcxxxxaj mc74hcxxxxan mc74hcxxxxad mc74hcxxxxadt ceramic plastic soic tssop 1 14 1 14 j suffix ceramic package case 63208 1 14 1 14 dt suffix tssop package case 948g01
mc54/74hc4016a motorola highspeed cmos logic data dl129 e rev 6 32 ??????????????????????? ??????????????????????? ??????????????????????? ??????????????????????? maximum ratings* ??? ??? ??? ??? symbol ?????????????? ?????????????? ?????????????? ?????????????? parameter ?????? ?????? ?????? ?????? value ??? ??? ??? ??? unit ??? ??? ??? ??? v cc ?????????????? ?????????????? ?????????????? ?????????????? positive dc supply voltage (referenced to gnd) ?????? ?????? ?????? ?????? 0.5 to + 14.0 ??? ??? ??? ??? v ??? ??? ??? ??? v is ?????????????? ?????????????? ?????????????? ?????????????? analog input voltage (referenced to gnd) ?????? ?????? ?????? ?????? 0.5 to v cc + 0.5 ??? ??? ??? ??? v ??? ??? ??? ??? v in ?????????????? ?????????????? ?????????????? ?????????????? digital input voltage (referenced to gnd) ?????? ?????? ?????? ?????? 0.5 to v cc + 0.5 ??? ??? ??? ??? v ??? ??? ??? ??? i ?????????????? ?????????????? ?????????????? ?????????????? dc current into or out of any pin ?????? ?????? ?????? ?????? 25 ??? ??? ??? ??? ma ??? ??? ??? ??? ??? p d ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? power dissipation in still air, plastic or ceramic dip2 soic package2 tssop package2 ?????? ?????? ?????? ?????? ?????? 750 500 450 ??? ??? ??? ??? ??? mw ??? ??? ??? ??? t stg ?????????????? ?????????????? ?????????????? ?????????????? storage temperature ?????? ?????? ?????? ?????? 65 to + 150 ??? ??? ??? ??? c ??? ??? ??? ??? ??? ??? t l ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? lead t emperature, 1 mm from case for 10 seconds (plastic dip, soic or tssop package) (ceramic dip) ?????? ?????? ?????? ?????? ?????? ?????? 260 300 ??? ??? ??? ??? ??? ??? c * maximum ratings are those values beyond which damage to the device may occur . functional operation should be restricted to the recommended operating conditions. 2derating e plastic dip: 10 mw/ c from 65 to 125 c ceramic dip: 10 mw/ c from 100 to 125 c soic package: 7 mw/ c from 65 to 125 c tssop package: 6.1 mw/ c from 65 to 125 c for high frequency or heavy load considerations, see chapter 2 of the motorola highspeed cmos data book (dl129/d). recommended operating conditions ???? ???? ???? ???? symbol ?????????????? ?????????????? ?????????????? ?????????????? parameter ??? ??? ??? ??? min ??? ??? ??? ??? max ??? ??? ??? ??? unit ???? ???? ???? ???? v cc ?????????????? ?????????????? ?????????????? ?????????????? positive dc supply voltage (referenced to gnd) ??? ??? ??? ??? 2.0 ??? ??? ??? ??? 12.0 ??? ??? ??? ??? v ???? ???? ???? ???? v is ?????????????? ?????????????? ?????????????? ?????????????? analog input voltage (referenced to gnd) ??? ??? ??? ??? gnd ??? ??? ??? ??? v cc ??? ??? ??? ??? v ???? ???? ???? ???? v in ?????????????? ?????????????? ?????????????? ?????????????? digital input voltage (referenced to gnd) ??? ??? ??? ??? gnd ??? ??? ??? ??? v cc ??? ??? ??? ??? v ???? ???? ???? ???? v io * ?????????????? ?????????????? ?????????????? ?????????????? static or dynamic voltage across switch ??? ??? ??? ??? e ??? ??? ??? ??? 1.2 ??? ??? ??? ??? v ???? ???? ???? ???? t a ?????????????? ?????????????? ?????????????? ?????????????? operating temperature, all package types ??? ??? ??? ??? 55 ??? ??? ??? ??? + 125 ??? ??? ??? ??? c ???? ???? ???? ???? ???? ???? ???? t r , t f ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? input rise and fall time, on/off v cc = 2.0 v control inputs (figure 10) v cc = 3.0 v v cc = 4.5 v v cc = 9.0 v v cc = 12.0 v ??? ??? ??? ??? ??? ??? ??? 0 0 0 0 0 ??? ??? ??? ??? ??? ??? ??? 1000 600 500 400 250 ??? ??? ??? ??? ??? ??? ??? ns * for voltage drops across the switch greater than 1.2 v (switch on), excessive v cc current may be drawn; i.e., the current out of the switch may contain both v cc and switch input components. the reliability of the device will be unaf fected unless the maximum ratings are exceeded. dc electrical characteristics digital section (voltages referenced to gnd) ???? ???? ???? ???? symbol ????????? ????????? ????????? ????????? parameter ????????? ????????? ????????? ????????? test conditions ???? ???? ???? ???? v cc v ????????? ????????? ????????? ????????? guaranteed limit ??? ??? ??? ??? unit ???? ???? ???? ???? symbol ????????? ????????? ????????? ????????? parameter ????????? ????????? ????????? ????????? test conditions ???? ???? ???? ???? v cc v ??? ??? ??? ??? 55 to 25 c ???? ???? ???? ???? 85 c ???? ???? ???? ???? 125 c ??? ??? ??? ??? unit ???? ???? ???? ???? ???? ???? ???? v ih ????????? ????????? ????????? ????????? ????????? ????????? ????????? minimum highlevel voltage on/off control inputs ????????? ????????? ????????? ????????? ????????? ????????? ????????? r on = per spec ???? ???? ???? ???? ???? ???? ???? 2.0 3.0 4.5 9.0 12.0 ??? ??? ??? ??? ??? ??? ??? 1.5 2.1 3.15 6.3 8.4 ???? ???? ???? ???? ???? ???? ???? 1.5 2.1 3.15 6.3 8.4 ???? ???? ???? ???? ???? ???? ???? 1.5 2.1 3.15 6.3 8.4 ??? ??? ??? ??? ??? ??? ??? v ???? ???? ???? ???? ???? ???? v il ????????? ????????? ????????? ????????? ????????? ????????? maximum lowlevel voltage on/off control inputs ????????? ????????? ????????? ????????? ????????? ????????? r on = per spec ???? ???? ???? ???? ???? ???? 2.0 3.0 4.5 9.0 12.0 ??? ??? ??? ??? ??? ??? 0.5 0.9 1.35 2.70 3.6 ???? ???? ???? ???? ???? ???? 0.5 0.9 1.35 2.70 3.6 ???? ???? ???? ???? ???? ???? 0.5 0.9 1.35 2.70 3.6 ??? ??? ??? ??? ??? ??? v this device contains protection circuitry to guard against damage due to high static voltages or electric fields. however , precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this highimpedance cir - cuit. for proper operation, v in and v out should be constrained to the range gnd (v in or v out ) v cc . unused inputs must always be tied to an appropriate logic voltage level (e.g., either gnd or v cc ). unused outputs must be left open. i/o pins must be connected to a properly terminated line or bus.
mc54/74hc4016a highspeed cmos logic data dl129 e rev 6 33 motorola dc electrical characteristics digital section (voltages referenced to gnd) ??? ??? ??? ??? unit ????????? ????????? ????????? ????????? guaranteed limit ???? ???? ???? ???? v cc v ????????? ????????? ????????? ????????? test conditions ????????? ????????? ????????? ????????? parameter ???? ???? ???? ???? symbol ??? ??? ??? ??? ??? unit ???? ???? ???? ???? ???? 125 c ???? ???? ???? ???? ???? 85 c ??? ??? ??? ??? ??? 55 to 25 c ???? ???? ???? ???? ???? v cc v ????????? ????????? ????????? ????????? ????????? test conditions ????????? ????????? ????????? ????????? ????????? parameter ???? ???? ???? ???? ???? symbol ???? ???? ???? ???? ???? i in ????????? ????????? ????????? ????????? ????????? maximum input leakage current, on/off control inputs ????????? ????????? ????????? ????????? ????????? v in = v cc or gnd ???? ???? ???? ???? ???? 12.0 ??? ??? ??? ??? ??? 0.1 ???? ???? ???? ???? ???? 1.0 ???? ???? ???? ???? ???? 1.0 ??? ??? ??? ??? ??? m a ???? ???? ???? ???? i cc ????????? ????????? ????????? ????????? maximum quiescent supply current (per package) ????????? ????????? ????????? ????????? v in = v cc or gnd v io = 0 v ???? ???? ???? ???? 6.0 12.0 ??? ??? ??? ??? 2 4 ???? ???? ???? ???? 20 40 ???? ???? ???? ???? 40 160 ??? ??? ??? ??? m a note: information on typical parametric values can be found in chapter 2 of the motorola highspeed cmos data book (dl129/d). dc electrical characteristics analog section (voltages referenced to gnd) ???? ???? ???? ???? symbol ????????? ????????? ????????? ????????? parameter ????????? ????????? ????????? ????????? test conditions ???? ???? ???? ???? v cc v ????????? ????????? ????????? ????????? guaranteed limit ??? ??? ??? ??? unit ???? ???? ???? ???? symbol ????????? ????????? ????????? ????????? parameter ????????? ????????? ????????? ????????? test conditions ???? ???? ???? ???? v cc v ??? ??? ??? ??? 55 to 25 c ???? ???? ???? ???? 85 c ???? ???? ???? ???? 125 c ??? ??? ??? ??? unit ???? ???? ???? ???? ???? ???? r on ????????? ????????? ????????? ????????? ????????? ????????? maximum aono resistance ????????? ????????? ????????? ????????? ????????? ????????? v in = v ih v is = v cc to gnd i s 2.0 ma (figures 1, 2) ???? ???? ???? ???? ???? ???? 2.02 4.5 9.0 12.0 ??? ??? ??? ??? ??? ??? e 160 90 90 ???? ???? ???? ???? ???? ???? e 200 110 110 ???? ???? ???? ???? ???? ???? e 240 130 130 ??? ??? ??? ??? ??? ??? w ???? ???? ???? ???? ???? ???? ????????? ????????? ????????? ????????? ????????? ????????? ????????? ????????? ????????? ????????? ????????? ????????? v in = v ih v is = v cc or gnd (endpoints) i s 2.0 ma (figures 1, 2) ???? ???? ???? ???? ???? ???? 2.0 4.5 9.0 12.0 ??? ??? ??? ??? ??? ??? e 90 70 70 ???? ???? ???? ???? ???? ???? e 115 90 90 ???? ???? ???? ???? ???? ???? e 140 105 105 ??? ??? ??? ??? ??? ??? ???? ???? ???? ???? ???? ???? d r on ????????? ????????? ????????? ????????? ????????? ????????? maximum difference in aono resistance between any two channels in the same package ????????? ????????? ????????? ????????? ????????? ????????? v in v ih v is = 1/2 (v cc gnd) i s 2.0 ma ???? ???? ???? ???? ???? ???? 2.0 4.5 9.0 12.0 ??? ??? ??? ??? ??? ??? e 20 15 15 ???? ???? ???? ???? ???? ???? e 25 20 20 ???? ???? ???? ???? ???? ???? e 30 25 25 ??? ??? ??? ??? ??? ??? w ???? ???? ???? ???? ???? i off ????????? ????????? ????????? ????????? ????????? maximum offchannel leakage current, any one channel ????????? ????????? ????????? ????????? ????????? v in = v il v io = v cc or gnd switch off (figure 3) ???? ???? ???? ???? ???? 12.0 ??? ??? ??? ??? ??? 0.1 ???? ???? ???? ???? ???? 0.5 ???? ???? ???? ???? ???? 1.0 ??? ??? ??? ??? ??? m a ???? ???? ???? ???? ???? ???? i on ????????? ????????? ????????? ????????? ????????? ????????? maximum onchannel leakage current, any one channel ????????? ????????? ????????? ????????? ????????? ????????? v in = v ih v is = v cc or gnd (figure 4) ???? ???? ???? ???? ???? ???? 12.0 ??? ??? ??? ??? ??? ??? 0.1 ???? ???? ???? ???? ???? ???? 0.5 ???? ???? ???? ???? ???? ???? 1.0 ??? ??? ??? ??? ??? ??? m a 2at supply voltage (v cc gnd) approaching 3 v the analog switchon resistance becomes extremely nonlinear. therefore, for lowvoltage operation, it is recommended that these devices only be used to control digital signals. note: information on typical parametric values can be found in chapter 2 of the motorola highspeed cmos data book (dl129/d). ac electrical characteristics (c l = 50 pf, on/off control inputs: t r = t f = 6 ns) ???? ???? ???? ???? symbol ????????????????? ????????????????? ????????????????? ????????????????? parameter ???? ???? ???? ???? v cc v ????????? ????????? ????????? ????????? guaranteed limit ??? ??? ??? ??? unit ???? ???? ???? ???? symbol ????????????????? ????????????????? ????????????????? ????????????????? parameter ???? ???? ???? ???? v cc v ??? ??? ??? ??? 55 to 25 c ???? ???? ???? ???? 85 c ???? ???? ???? ???? 125 c ??? ??? ??? ??? unit ???? ???? ???? ???? ???? ???? t plh , t phl ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? maximum propagation delay , analog input to analog output (figures 8 and 9) ???? ???? ???? ???? ???? ???? 2.0 4.5 9.0 12.0 ??? ??? ??? ??? ??? ??? 40 5 5 5 ???? ???? ???? ???? ???? ???? 50 7 7 7 ???? ???? ???? ???? ???? ???? 60 8 8 8 ??? ??? ??? ??? ??? ??? ns ???? ???? ???? ???? ???? ???? t plz , t phz ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? maximum propagation delay, on/off control to analog output (figures 10 and 11) ???? ???? ???? ???? ???? ???? 2.0 4.5 9.0 12.0 ??? ??? ??? ??? ??? ??? 80 20 20 20 ???? ???? ???? ???? ???? ???? 90 25 25 25 ???? ???? ???? ???? ???? ???? 110 35 35 35 ??? ??? ??? ??? ??? ??? ns ???? ???? ???? ???? ???? ???? t pzl , t pzh ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? maximum propagation delay, on/off control to analog output (figures 10 and 11) ???? ???? ???? ???? ???? ???? 2.0 4.5 9.0 12.0 ??? ??? ??? ??? ??? ??? 80 20 20 20 ???? ???? ???? ???? ???? ???? 90 25 25 25 ???? ???? ???? ???? ???? ???? 100 30 30 30 ??? ??? ??? ??? ??? ??? ns
mc54/74hc4016a motorola highspeed cmos logic data dl129 e rev 6 34 ac electrical characteristics (c l = 50 pf, on/off control inputs: t r = t f = 6 ns) ??? ??? ??? ??? unit ????????? ????????? ????????? ????????? guaranteed limit ???? ???? ???? ???? v cc v ????????????????? ????????????????? ????????????????? ????????????????? parameter ???? ???? ???? ???? symbol ??? ??? ??? ??? ??? unit ???? ???? ???? ???? ???? 125 c ???? ???? ???? ???? ???? 85 c ??? ??? ??? ??? ??? 55 to 25 c ???? ???? ???? ???? ???? v cc v ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? parameter ???? ???? ???? ???? ???? symbol ???? ???? ???? ???? c ????????????????? ????????????????? ????????????????? ????????????????? maximum capacitance on/off control input ???? ???? ???? ???? e ??? ??? ??? ??? 10 ???? ???? ???? ???? 10 ???? ???? ???? ???? 10 ??? ??? ??? ??? pf ???? ???? ???? ???? ???? ????????????????? ????????????????? ????????????????? ????????????????? ????????????????? control input = gnd analog i/o feedthrough ???? ???? ???? ???? ???? e e ??? ??? ??? ??? ??? 35 1.0 ???? ???? ???? ???? ???? 35 1.0 ???? ???? ???? ???? ???? 35 1.0 ??? ??? ??? ??? ??? notes: 1. for propagation delays with loads other than 50 pf , see chapter 2 of the motorola highspeed cmos data book (dl129/d). 2. information on typical parametric values can be found in c hapter 2 of the motorola highspeed cmos data book (dl129/d). c pd power dissipation capacitance (per switch)* (figure 13) typical @ 25 c, v cc = 5.0 v pf c pd power dissipation capacitance (per switch)* (figure 13) 15 pf * used to determine the noload dynamic power consumption: p d = c pd v cc 2 f + i cc v cc . for load considerations, see chapter 2 of the motorola highspeed cmos data book (dl129/d). additional application characteristics (voltages referenced to gnd unless noted) ???? ???? ???? ???? ???? symbol ?????????? ?????????? ?????????? ?????????? ?????????? parameter ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? test conditions ??? ??? ??? ??? ??? v cc v ???? ???? ???? ???? ???? limit* 25 c 54/74hc ??? ??? ??? ??? ??? unit ???? ???? ???? ???? ???? ???? bw ?????????? ?????????? ?????????? ?????????? ?????????? ?????????? maximum onchannel bandwidth or minimum frequency response (figure 5) ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? f in = 1 mhz sine wave adjust f in voltage to obtain 0 dbm at v os increase f in frequency until db meter reads 3 db r l = 50 w , c l = 10 pf ??? ??? ??? ??? ??? ??? 4.5 9.0 12.0 ???? ???? ???? ???? ???? ???? 150 160 160 ??? ??? ??? ??? ??? ??? mhz ???? ???? ???? ???? ???? e ?????????? ?????????? ?????????? ?????????? ?????????? of fchannel feedthrough isolation (figure 6) ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? f in sine wave adjust f in voltage to obtain 0 dbm at v is f in = 10 khz, r l = 600 w , c l = 50 pf ??? ??? ??? ??? ??? 4.5 9.0 12.0 ???? ???? ???? ???? ???? 50 50 50 ??? ??? ??? ??? ??? db ???? ???? ???? ???? ???? ???? ?????????? ?????????? ?????????? ?????????? ?????????? ?????????? ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? f in = 1.0 mhz, r l = 50 w , c l = 10 pf ??? ??? ??? ??? ??? ??? 4.5 9.0 12.0 ???? ???? ???? ???? ???? ???? 40 40 40 ??? ??? ??? ??? ??? ??? ???? ???? ???? ???? ???? e ?????????? ?????????? ?????????? ?????????? ?????????? feedthrough noise, control to switch (figure 7) ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? v in 1 mhz square wave (t r = t f = 6 ns) adjust r l at setup so that i s = 0 a r l = 600 w , c l = 50 pf ??? ??? ??? ??? ??? 4.5 9.0 12.0 ???? ???? ???? ???? ???? 60 130 200 ??? ??? ??? ??? ??? mv pp ???? ???? ???? ???? ???? ?????????? ?????????? ?????????? ?????????? ?????????? ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? r l = 10 k w , c l = 10 pf ??? ??? ??? ??? ??? 4.5 9.0 12.0 ???? ???? ???? ???? ???? 30 65 100 ??? ??? ??? ??? ??? ???? ???? ???? ???? ???? ???? e ?????????? ?????????? ?????????? ?????????? ?????????? ?????????? crosstalk between any two switches (figure 12) ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? f in sine wave adjust f in voltage to obtain 0 dbm at v is f in = 10 khz, r l = 600 w , c l = 50 pf ??? ??? ??? ??? ??? ??? 4.5 9.0 12.0 ???? ???? ???? ???? ???? ???? 70 70 70 ??? ??? ??? ??? ??? ??? db ???? ???? ???? ???? ???? ?????????? ?????????? ?????????? ?????????? ?????????? ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? f in = 1.0 mhz, r l = 50 w , c l = 10 pf ??? ??? ??? ??? ??? 4.5 9.0 12.0 ???? ???? ???? ???? ???? 80 80 80 ??? ??? ??? ??? ??? ???? ???? ???? ???? ???? ???? ???? thd ?????????? ?????????? ?????????? ?????????? ?????????? ?????????? ?????????? total harmonic distortion (figure 14) ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? ?????????????? f in = 1 khz, r l = 10 k w , c l = 50 pf thd = thd measured thd source v is = 4.0 v pp sine wave v is = 8.0 v pp sine wave v is = 11.0 v pp sine wave ??? ??? ??? ??? ??? ??? ??? 4.5 9.0 12.0 ???? ???? ???? ???? ???? ???? ???? 0.10 0.06 0.04 ??? ??? ??? ??? ??? ??? ??? % * guaranteed limits not tested. determined by design and verified by qualification.
mc54/74hc4016a highspeed cmos logic data dl129 e rev 6 35 motorola 160 140 120 100 80 60 40 20 0 0 .5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 120 100 80 60 40 20 0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 80 70 60 50 40 30 20 10 0 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 v in , input voltage (volts), referenced to gnd v in , input voltage (volts), referenced to gnd v in , input voltage (volts), referenced to gnd figure 1b. typical on resistance, v cc = 4.5 v figure 1d. typical on resistance, v cc = 9.0 v figure 1c. typical on resistance, v cc = 6.0 v figure 1e. typical on resistance, v cc = 12.0 v 3000 2500 2000 1500 1000 500 0 0 .25 .50 .75 1.00 1.25 1.5 1.75 2.00 300 250 200 150 100 50 0 0 .5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 v in , input voltage (volts), referenced to gnd v in , input voltage (volts), referenced to gnd r on figure 1a. typical on resistance, v cc = 2.0 v figure 2. on resistance test setup plotter mini computer programmable power supply dc analyzer v cc + analog in common out gnd device under test , on resist ance (ohms) r on , on resist ance (ohms) r on , on resist ance (ohms) r on , on resist ance (ohms) r on , on resist ance (ohms) tbd tbd tbd tbd tbd
mc54/74hc4016a motorola highspeed cmos logic data dl129 e rev 6 36 figure 3. maximum off channel leakage current, any one channel, test setup off 7 14 v cc a v cc gnd v cc selected control input v il figure 4. maximum on channel leakage current, channel to channel, test setup on 14 v cc n/c a gnd v cc 7 selected control input v ih figure 5. maximum onchannel bandwidth test setup on 14 v cc 0.1 m f c l * f in db meter *includes all probe and jig capacitance. v os 7 selected control input v cc figure 6. offchannel feedthrough isolation, test setup off 7 14 v cc 0.1 m f c l * f in db meter *includes all probe and jig capacitance. v os r l v is selected control input figure 7. feedthrough noise, on/off control to analog out, test setup 14 v cc c l * *includes all probe and jig capacitance. off/on v cc gnd v in 1 mhz t r = t f = 6 ns control v cc/2 r l i s r l v os 7 selected control input v cc/2 v cc gnd analog in analog out 50% t plh t phl 50% figure 8. propagation delays, analog in to analog out
mc54/74hc4016a highspeed cmos logic data dl129 e rev 6 37 motorola figure 9. propagation delay test setup on 14 v cc *includes all probe and jig capacitance. test point analog out analog in c l * 7 selected control input v cc t r t f v cc gnd high impedance v ol v oh high impedance control analog out 90% 50% 10% 50% 50% 10% 90% t pzh t phz t pzl t plz figure 10. propagation delay, on/off control to analog out on/off v cc test point 14 v cc 1 k w position when testing t phz and t pzh c l * 1 2 1 2 figure 11. propagation delay test setup 1 2 position when testing t plz and t pzl 7 selected control input figure 12. crosstalk between any two switches, test setup r l on 14 v cc or gnd c l * *includes all probe and jig capacitance off r l r l v is r l c l * v os f in 0.1 m f v cc/2 v cc/2 7 selected control input v cc/2 figure 13. power dissipation capacitance test setup 14 v cc nc off/on a nc 7 selected control input on/off control on v cc 0.1 m f c l * f in r l to distortion meter *includes all probe and jig capacitance. v os v is 7 selected control input v cc figure 14. total harmonic distortion, test setup *includes all probe and jig capacitance. v cc v cc/2
mc54/74hc4016a motorola highspeed cmos logic data dl129 e rev 6 38 0 10 20 30 40 50 100 1.0 2.0 frequency (khz) dbm 60 70 80 90 fundamental frequency device source figure 15. plot, harmonic distortion 3.0 application information the on/off control pins should be at v cc or gnd logic levels, v cc being recognized as logic high and gnd being recognized a s a l ogi c l ow . u nuse d a nalo g i nputs/outputs may be left floating (not connected). however, it is advisable to t i e u nuse d a nalo g i nput s a n d o utput s t o v cc o r g nd through a low value resistor . this minimizes crosstalk and feedthrough noise that may be picked up by the unused i/o pins. the maximum analog voltage swings are determined by the supply voltages v cc and gnd. the positive peak analog voltage should not exceed v cc . similarly, the negative peak analog voltage should not go below gnd. in the example below, the difference between v cc and gnd is twelve volts. therefore, using the configuration in figure 16, a maximum analog s igna l o f t welv e v olt s p eaktopea k c a n b e c on- trolled. when voltage transients above v cc and/or below gnd are anticipated on the analog channels, external diodes (dx) are r ecommende d a s s hown i n f igur e 1 7 . t hes e d iodes should be small signal, fast turnon types able to absorb the maximum anticipated current surges during clipping. an al - ternate m etho d w oul d b e t o r eplac e t h e d x d iode s w ith mo sorbs ( motorol a h ig h c urren t s urg e p rotectors). mo sorbs are fast turnon devices ideally suited for precise dc protection with no inherent wearout mechanism. analog o/i on 14 v cc = 12 v analog i/o + 12 v 0 v + 12 v 0 v other control inputs (v cc or gnd) on 14 v cc d x d x v cc d x figure 16. 12 v application figure 17. transient suppressor application 7 selected control input d x other control inputs (v cc or gnd) 7 selected control input + 12 v v cc
mc54/74hc4016a highspeed cmos logic data dl129 e rev 6 39 motorola + 5 v 14 hc4016 control inputs 7 5 6 14 15 lsttl/ nmos analog signals r* r* r* r* analog signals hct buffer r* = 2 to 10 k w v dd = 5 v v cc = 5 to 12 v analog signals analog signals 1 16 14 hc4016 control inputs 7 8 mc14504 13 3 5 7 9 11 14 2 4 6 10 5 6 14 15 channel 4 channel 3 channel 2 channel 1 1 of 4 switches common i/o 1 2 3 4 control inputs input output 0.01 m f lf356 or equivalent a. using pull-up resistors b. using hct buffer figure 18. lsttl/nmos to hcmos interface figure 19. ttl/nmostocmos level converter analog signal peaktopeak greater than 5 v (also see hc4316a) figure 20. 4input multiplexer figure 21. sample/hold amplifier + 1 of 4 switches + 5 v 14 hc4016 control inputs 7 5 6 14 15 lsttl/ nmos analog signals analog signals 1 of 4 switches 1 of 4 switches 1 of 4 switches
mc54/74hc4016a motorola highspeed cmos logic data dl129 e rev 6 310 outline dimensions j suffix ceramic dip package case 63208 issue y min min max max inches millimeters dim a b c d f g j k l m n 0.785 0.280 0.200 0.020 0.065 0.015 0.170 15 0.040 0.750 0.245 0.155 0.015 0.055 0.008 0.125 0 0.020 19.94 7.11 5.08 0.50 1.65 0.38 4.31 15 1.01 19.05 6.23 3.94 0.39 1.40 0.21 3.18 0 0.51 0.100 bsc 0.300 bsc 2.54 bsc 7.62 bsc notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. dimension l to center of lead when formed parallel. 4. dimesnion f may narrow to 0.76 (0.030) where the lead enters the ceramic body. 14 8 1 7 -a- -b- -t- seating plane f g n k c l m 0.25 (0.010) t a m s 0.25 (0.010) t b m s j 14 pl d 14 pl n suffix plastic dip package case 64606 issue l notes: 1. leads within 0.13 (0.005) radius of true position at seating plane at maximum material condition. 2. dimension l to center of leads when formed parallel. 3. dimension b does not include mold flash. 4. rounded corners optional. 1 7 14 8 b a f h g d k c n l j m seating plane dim min max min max millimeters inches a 0.715 0.770 18.16 19.56 b 0.240 0.260 6.10 6.60 c 0.145 0.185 3.69 4.69 d 0.015 0.021 0.38 0.53 f 0.040 0.070 1.02 1.78 g 0.100 bsc 2.54 bsc h 0.052 0.095 1.32 2.41 j 0.008 0.015 0.20 0.38 k 0.115 0.135 2.92 3.43 l 0.300 bsc 7.62 bsc m 0 10 0 10 n 0.015 0.039 0.39 1.01
mc54/74hc4016a highspeed cmos logic data dl129 e rev 6 311 motorola outline dimensions d suffix plastic soic package case 751a03 issue f min min max max millimeters inches dim a b c d f g j k m p r 8.55 3.80 1.35 0.35 0.40 0.19 0.10 0 5.80 0.25 8.75 4.00 1.75 0.49 1.25 0.25 0.25 7 6.20 0.50 0.337 0.150 0.054 0.014 0.016 0.008 0.004 0 0.228 0.010 0.344 0.157 0.068 0.019 0.049 0.009 0.009 7 0.244 0.019 1.27 bsc 0.050 bsc notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimensions a and b do not include mold protrusion. 4. maximum mold protrusion 0.15 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.127 (0.005) total in excess of the d dimension at maximum material condition. a b p 7 pl g c k seating plane d 14 pl m j r x 45 1 7 8 14 0.25 (0.010) t b a m s s b 0.25 (0.010) m m f dt suffix plastic tssop package case 948g01 issue o dim min max min max inches millimeters a 4.90 5.10 0.193 0.200 b 4.30 4.50 0.169 0.177 c 1.20 0.047 d 0.05 0.15 0.002 0.006 f 0.50 0.75 0.020 0.030 g 0.65 bsc 0.026 bsc h 0.50 0.60 0.020 0.024 j 0.09 0.20 0.004 0.008 j1 0.09 0.16 0.004 0.006 k 0.19 0.30 0.007 0.012 k1 0.19 0.25 0.007 0.010 l 6.40 bsc 0.252 bsc m 0 8 0 8 notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimension a does not include mold flash, protrusions or gate burrs. mold flash or gate burrs shall not exceed 0.15 (0.006) per side. 4. dimension b does not include interlead flash or protrusion. interlead flash or protrusion shall not exceed 0.25 (0.010) per side. 5. dimension k does not include dambar protrusion. allowable dambar protrusion shall be 0.08 (0.003) total in excess of the k dimension at maximum material condition. 6. terminal numbers are shown for reference only. 7. dimension a and b are to be determined at datum plane w. s u 0.15 (0.006) t 2x l/2 s u m 0.10 (0.004) v s t l u seating plane 0.10 (0.004) t ??? ??? ??? ??? section nn detail e j j1 k k1 detail e f m w 0.25 (0.010) 8 14 7 1 pin 1 ident. h g a d c b s u 0.15 (0.006) t v 14x ref k n n
mc54/74hc4016a motorola highspeed cmos logic data dl129 e rev 6 312 how to reach us: usa/europe : motorola literature distribution; japan : nippon motorola ltd.; tatsumispdjldc, toshikatsu otsuki, p.o. box 20912; phoenix, arizona 85036. 18004412447 6f seibubutsuryucenter, 3142 tatsumi kotoku, tokyo 135, japan. 0335218315 mfax : rmf ax0@email.sps.mot.com touchtone (602) 2446609 hong kong : motorola semiconductors h.k. ltd.; 8b tai ping industrial park, internet : http://designnet.com 51 ting kok road, tai po, n.t., hong kong. 85226629298 motorola reserves the right to make changes without further notice to any products herein. motorola makes no warranty , representation or guarantee regarding the suitability of its products for any particular purpose, nor does motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability , including without limitation consequential or incidental damages. at ypicalo parameters can and do vary in dif ferent applications. all operating parameters, including at ypicalso must be validated for each customer application by customer ' s technical experts. motorola does not convey any license under its patent rights nor the rights of others. motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body , or other applications intended to support or sustain life, or for any other application in which the failure of the motorola product could create a situation where personal injury or death may occur . should buyer purchase or use motorola products for any such unintended or unauthorized application, buyer shall indemnify and hold motorola and its of ficers, employees, subsidiaries, af filiates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly , any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that motorola was negligent regarding the design or manufacture of the part. motorola and are registered trademarks of motorola, inc. motorola, inc. is an equal opportunity/af firmative action employer . mc54/74hc4016a/d

? codeline

▲Up To Search▲

Price & Availability of MC74HC4016A

	To Download MC74HC4016A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .